Balinsasayao Twin Lakes Natural Park is a mountainous natural park of 80km² in the Cuernos de Negros mountain chain between Dumaguete and San Jose. It contains one of the last stretches of primary forest in Negros, and the Philippines. Economical interests and illegal deforestation put pressure on this last stretch of highland tropical forest. To put a halt to the illegal deforestation, the PAMB (protected area management board) of the park wants to more tightly monitor the stretches of forest. Due to the size of the park and limited personnel availability, it takes a lot of time to monitor the whole park on foot. To aid their monitoring they looked at the possibilities of a technological solution to aid the monitoring. At a presentation of the PAMB, the Nightowl Technology Incubator and Hackerspace was asked if UAV's (drones) could be an option in monitoring this area. Due to the limitations of flight time (around 20min) and signal range (3km) of the remote controller, regular drones are not practical for this purpose. If UAV's could monitor this area autonomously on the other hand, it would greatly improve the monitoring capabilities. Commercial autonomous UAV's are cost-prohibitive for this application though. If we could device a low-cost, DYI, open source autonomous UAV system, we could use it to assist both the Balinsasayao National Park but it could also be a very interesting project for other areas, and has commercial potential as well. This is pushing the boundaries of drones though, and will require many different technologies to be applied and combined and possibly developed. As such it is an ambitious project that requires a lot of Research and Development, and the outcome is far from certain. The Nightowl Incubator and Maker-Space, where ambitious students and makers are available, is the ideal location to take on this long-term project, and tackle the problems one by one. But without both financial and practical aid this will be a difficult task. Financial aid needs to be found form DENR, DOST and other government agencies, and partnerships need to be found with other groups within and outside universities to get the best people together.

This project will be purely an R&D/prototyping project. The goal is to investigate whether it is possible to develop a UAV system with a limited budget and technical resources, and by using as many existing open-source components as possible, that is able to operate without human intervention or purely remote (km's away) human intervention. There are many aspects and requirements to this project that are all ambitious. Some of the aspects of the project might have the outcome that more work is needed, or the required technology doesn't exist yet or is still cost-prohibitive, and therefore the application as described in the introduction is not possible at this time. For the components that are deemed feasible, the project will try to develop and test the components, and document the whole process for use by others. All components and software that need to be developed within this project will be made available under an open-source license, and will be published online, available to the general public.

• Be able to fly between base stations of a fixed, known location, in an area without obstructions above a minimum altitude
• Land at the base stations accurately enough to allow wireless charging
• Record photo or video data along the way
• Possibly transfer the data at the base stations after landing
• Possibly receive instructions from the base stations and/or a central management tool/person for the next flight
• The UAV should be easily locatable in case of a crash or other problem
• It should be able to charge it batteries wirelessly

• Provide electricity to charge the drone batteries (solar?)
• Be able to charge the drone batteries wirelessly
• Provide a dry and shaded area for the drone to recharge, but also land and take-off accurately
• Optional: through a mesh network or cellphone reception connect to a centralized management application on the internet
• Optional: Communicate simple instructions to the drone for route planning

The necessity of this application is not certain and depends on the possibilities of the drone and it's base station. Optional requirements could be:

• Monitor weather conditions to evaluate of they are suitable for the UAV to fly
• Plan the route of the UAV
• Provide a log of the activities and different metrics of the UAV and it's base stations
• Monitor the location of the UAV in case of problems
• Provide information on the health of the UAV and base stations and notify a user if required

Milestones

1. Finalize current proposal
   • Finalize design requirements for first proposal
   • Research combination of flight time, range and wireless signal strength on 2.4GHz (possibly with nrf24L+)
   • Research accurate landing (laser, infrared, etc)
   • Research drone controllers, IMU and GPS communication
   • Research routing software (mission planning/operation)
   • Research altitude navigation for landing and sensors
   • Research flight duration
   • Get a list of materials
   • Finalize milestone list

• Water proof for water crash?
• Find back in case of problems (sensor/signal)
• Wireless communication throughout flight to relocate it later on?

• The NRF24L01+ with antenna, PA and LNA (power amplifier and low noise amplifier) can have around 300-1000m range, we could use that to transmit the location of the drone in flight, so we know where it goes down. Disadvantage is it's bulk and probably larger battery requirement (and thus weight). We could also use it to keep sending the drone GPS coordinates out on 2.4GHz from the GPS module. See http://www.elecfreaks.com/wiki/index.php?title=2.4G_Wireless_nRF24L01p_with_PA_and_LNA. The price is good at around $15 for two modules. See http://www.ebay.com/itm/2-x-NRF24L01-PA-LNA-SMA-Antenna-Wireless-Transceiver-communication-module-2-4G-/111853679356
• Loc8tor lite is a tag with locator that can find the tag back accurately from 122m: http://www.loc8tor.com/everyday/loc8tor-lite.html/ This would be good for the last little stretch in a forest, but costs $90.
• A complete, but expensive solution is from the Marco Polo locator at close to $300. http://eurekaproducts.com/product-category/buyrcmodelsystems/
• A DIY telemetry kit with around 700m range (open field) is possible for around $20 as well. This seems a very good option right now. See https://quadmeup.com/diy-wireless-telemetry-link-for-uav/

There is an irlock module available for precision landing. It is an IR sensor that centers the drone over a location. It is compatible with the dronecode/ardupilot suite of software. See http://ardupilot.org/copter/docs/precision-landing-with-irlock.html

• https://www.dronecode.org/dronecode-software-platform
• http://elinux.org/images/4/49/Autonomous_Navigation_for_an_OMAP4_Nano-Drone.pdf
• http://px4.io/
• https://pixhawk.org/
• https://store.3dr.com/products/3dr-pixhawk
• http://ardupilot.org/copter/index.html
• http://www.auav.co/category-s/100.htm
• https://en.wikipedia.org/wiki/Unmanned_aerial_vehicle#Autonomy
• Wireless charging for the Base stations: http://www.instructables.com/id/Wireless-Electricity-Transmission-Simple-things-re/
• http://diydrones.com/
• http://copter.ardupilot.org/ardupilot/index.html
• http://ardupilot.org/ardupilot/index.html
• https://docs.google.com/document/d/10MgFocP4nxi_uPrZQDXdhGncASnwSeg1XHiWnK9IcvI/edit?usp=sharing